3D Printed Door Panel Light Lenses
-
- Posts: 261
- Joined: Sat Apr 25, 2020 9:27 pm
- TOA Membership Number: 0
- Years Owned: 1969 Oldsmobile Toronado
Re: 3D Printed Door Panel Light Lenses
If you guys need any I can create more and sell them to you. Although the light emitted will be slightly lower, they are more durable than the original lens (I might create a video demonstration later this week). Just let me know through email or private message.
- Otto Skorzeny
- Posts: 1720
- Joined: Fri Feb 28, 2014 12:41 pm
- TOA Membership Number: 0
- Years Owned: 1966 Toronado
Re: 3D Printed Door Panel Light Lenses
I'm thinking about backup lenses for my '56 Cadillac! Let me get a list together!
-
- Posts: 261
- Joined: Sat Apr 25, 2020 9:27 pm
- TOA Membership Number: 0
- Years Owned: 1969 Oldsmobile Toronado
Re: 3D Printed Door Panel Light Lenses
Haha, but I would need some sort of reference or sketch with dimensions to be able to create a model.
-
- Posts: 261
- Joined: Sat Apr 25, 2020 9:27 pm
- TOA Membership Number: 0
- Years Owned: 1969 Oldsmobile Toronado
Re: 3D Printed Door Panel Light Lenses
I am also going to start designing a pair for the rear courtesy lights probably by next week so I’ll keep everyone updated on that. So far, I can only make and sell interior plastic parts for 1st gen Toronados (interior didn’t really change at all between 66-69). If it’s meant for the exterior and you plan on making it a showroom car, I would think that it’s a better option to buy an oem replacement because of the finish. If I did, I would only make those for the ‘69 and maybe the ‘68 (don’t have a reference for ‘66 and ‘67).
Re: 3D Printed Door Panel Light Lenses
Hi ! That's great to see someone else using a 3d printer to restore our lovely Toronado ![Smile :)](./images/smilies/icon_e_smile.gif)
I have done the same for multiple parts, I was thinking we could do a new Topic in the parts section with our 3d creations.
So far I have done some small plastic parts, the back courtesy lens and a new support for a new radiator, the old one was too far gone and the original support did not fit and was too rusty...
In my opinion, 3d printers are a solution for rare/expensive parts, and will be used more and more by collectors.
https://www.mercedes-benz.com/en/classi ... d-printer/
And yes it's only plastic but if the part fit perfectly, you can send it to a website that will print in metal or whatever you want![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)
I have done the same for multiple parts, I was thinking we could do a new Topic in the parts section with our 3d creations.
So far I have done some small plastic parts, the back courtesy lens and a new support for a new radiator, the old one was too far gone and the original support did not fit and was too rusty...
In my opinion, 3d printers are a solution for rare/expensive parts, and will be used more and more by collectors.
https://www.mercedes-benz.com/en/classi ... d-printer/
And yes it's only plastic but if the part fit perfectly, you can send it to a website that will print in metal or whatever you want
![Smile :)](./images/smilies/icon_e_smile.gif)
- Attachments
-
- Screenshot 2020-12-19 103637.png (630.4 KiB) Viewed 17299 times
-
- IMG_20190314_201702.jpg (1.36 MiB) Viewed 17299 times
-
- IMG_20190310_194547.jpg (1.32 MiB) Viewed 17299 times
Re: 3D Printed Door Panel Light Lenses
All the parts I have done so far ![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)
- Attachments
-
- Screenshot 2020-12-19 104149.png (1.11 MiB) Viewed 17298 times
- Otto Skorzeny
- Posts: 1720
- Joined: Fri Feb 28, 2014 12:41 pm
- TOA Membership Number: 0
- Years Owned: 1966 Toronado
Re: 3D Printed Door Panel Light Lenses
Francois, on your brake booster vacuum valve, what did you do about the internal valve?
Re: 3D Printed Door Panel Light Lenses
Hi Otto,
It's not finished yet, it will be in two parts with a round cut in a nitrile rubber sheet that will act as the one way valve.
It's not finished yet, it will be in two parts with a round cut in a nitrile rubber sheet that will act as the one way valve.
-
- Posts: 261
- Joined: Sat Apr 25, 2020 9:27 pm
- TOA Membership Number: 0
- Years Owned: 1969 Oldsmobile Toronado
Re: 3D Printed Door Panel Light Lenses
Nice! That’s a lot of parts too haha. How do those rear courtesy lights look in your car? Do you have a picture of them by any chance? I think it’s a good idea to make a thread dedicated to 3D printing so we can let others know about it and maybe others can share their creations too.
-
- Posts: 261
- Joined: Sat Apr 25, 2020 9:27 pm
- TOA Membership Number: 0
- Years Owned: 1969 Oldsmobile Toronado
Re: 3D Printed Door Panel Light Lenses
Kinda took a while to do this because of school, but here it is. They are pretty tight when putting them on but they work nonetheless. Sucks that I accidentally broke one of the legs for the passenger side lens, but it’s not noticeable (I’ll fix it later).
The picture with the lens in the car was just a lighting test so that’s why it’s partially out.
The picture with the lens in the car was just a lighting test so that’s why it’s partially out.
- Attachments
-
- 3A46C758-96EA-4E61-A4F7-DDBA8C4C64FC.jpeg (45.23 KiB) Viewed 17001 times
-
- 63BD16C7-2EEB-4CC3-8E8E-8509FBF7E732.jpeg (45.84 KiB) Viewed 17001 times
-
- BE6DEE34-C2EB-497C-B234-851EBC1C5A9A.jpeg (48.59 KiB) Viewed 17001 times
Who is online
Users browsing this forum: No registered users and 7 guests